|
Download
：
【
Software
】
【
64Driver
】
【
Manual
】
【
Firmware
】
【
SDK
】
Introduction
：60MHz Hand-held Bandwidth Oscilloscope, 1GSa/ssample rate, 1M Memory Depth, and 6000 Counts DMM with analog bargraph.5.6 inch TFT Color LCD Display, High Resolution (640*480),High capacitance battery included (6 hours opreation time).
Accessories
OtherPictures
Characteristics (Handheld Oscilloscope/Multimeter)
•
High Bandwidth 60MHz Oscilloscope, 1GS/s sample rate, and 6000 Counts DMM with analog bargraph.
•
1M MemoryDepth.
•
High Refresh Rate (2500 frames)
•
Large 5.6 inch TFT Color LCD Display
，
High Resolution (640*480)
, Dual-Window Design --More clear, More Detailed
•
One-touch automatic setup optimizes the position, range, timebase, and triggering to assure a stable display of virtually any waveform
•
Easy-to-usepop-up menu with built-in multi-language help system
•
23 Automatic Measurements
•
Waveform Math: Add, Subtract, Multiply, and Divide
•
Store and recall over
•
Automatic cursor tracking measurements
•
XY Mode
•
Built-in FFT function converts a time-domain signal into its frequency components to measure harmonic content and distortion in systems
•
Waveform Recorder to capture/replay input waveforms from CH1 and CH2 with a maximum record length of 1000 frames
•
Pass-Fail function compares a stored waveform to an unknown input
•
Average Mode for smoothing waveforms
•
Square WaveOutput (2V, 1kHz) for probe adjustment
•
USB Host/Device 2.0 full-speed interface, support removeable disk, LAN Optional, Easy to control by PC or long-distance.
•
Dimensions (mm):240(L)x165(W)x50(H), device can be carried easily.
•
LabviewVBVC Second Design instance.
Hardware Specification
|
Model |
DSO1202B |
DSO1102B |
DSO1062B |
|
Oscilloscope mode |
|
Bandwidth |
200MHz |
100MHz |
60MHz |
|
Real-time Sample Rate |
1GSa/s |
|
Equivalent Sample Rate |
25GSa/s |
|
Record Length (Sample Points) |
Single-channel: Maximum 1M; Dual-channel:Maximum 512k |
|
SEC/DIV Range |
2nS/div-2000S/div (in a 2, 4, 8 sequence) |
|
Delay Time Accuracy |
500ps |
|
Vertical |
|
A/D Converter |
8-bit resolution |
|
VOLTS/DIV Range |
2mV/div
～
5V/div at input BNC |
|
Position
Range |
±50V(5V/div),±40V(2V/div
～
500mV/div),2V(200mV/div
～
50mV/div)±400mV(20mV/div
～
2mV/div) |
|
Rise Time at BNC |
≤
1.7ns |
≤
3.5ns |
≤
5.8ns |
|
DC Gain Accuracy |
±4% for Sample or Average acquisition mode, 5mV/div to 2mV/div
±3% for Sample or Average acquisition mode, 5V/div to 10mV/div |
|
Trigger |
|
Trigger Sensitivity
(Edge Trigger Type) |
DC: CH1/CH2 (Typical) 1div from DC to 10MHz;1.5div from 10MHz to Full
EXT
（
Typical
）
200mV from DC to 40MHz
EXT/5
（
Typical
）
1V from DC to 40MHz
AC: Attenuates signals below 10Hz
HF Reject: Attenuates signals above 80kHz
LF Reject: Attenuates signals below 150kHz
Noise Reject: Reduces trigger sensitivity |
|
Trigger
Level Range |
CH1,CH2: ±8 divisions from center of screen
EXT: ±1.2V EXT/5: ±6V |
|
Trigger Level Accuracy,
typical (Accuracy is for signals having rise and fall times ≥20ns) |
CH1,CH2: ±(0.3div×V/div) (within ±4 divisions from center of screen)
|
|
Holdoff
Range |
100ns-10s |
|
Trigger Type |
|
Edge |
Trigger on the rising or falling edge |
|
Pulse Width |
Trigger (when >,<,=,≠) on positive or negative pulses
Pulse Width Range: 20ns-10s |
|
Video |
Trigger on an NTSC, PAL, or SECAM standard video signal
Line Range: 1-525 (NTSC), 1-625 (PAL/SECAM) |
|
Slope |
Trigger (when >,<,=,≠) on a positive or negative slope
Set Time: 20ns–10s |
|
Overtime |
from the rising or falling edge
Set Time: 20ns-10s |
|
Alternate |
Internal trigger on edge, pulse width, video or slope |
|
Measurement |
|
Cursors |
Manual: The difference between voltage cursors △
V; the difference between time cursors △
T; 1/△
T calculated by Hz.
Tracing: The voltage and time at a waveform point |
|
Automatic |
Pk-Pk, Max, Min, Mean, Cyc RMS, Frequency, Period, Rise Time, Fall Time, Positive Width, Negative Width |
|
Meter Mode |
|
Max.Resolution |
6,000 Counts |
|
DMM Testing Modes |
Voltage, Current, Resistance, Capacitance,Diode & Continuity |
|
Max. Input Voltage |
AC: 600V, DC: 800V |
|
Max. Input Current |
AC: 10A, DC: 10A |
|
Input Impedance |
10 MΩ |
|
Display |
|
Type |
Right angle 5.6 16-digit color LCD |
|
Resolution |
640*480 dots |
|
Contrast |
16 gears, with the progress bar to show adjustment |
|
Interface |
USB host and USB slave, Lan Optional |
|
Power Supply |
|
Voltage |
DC Input:12--17VDC, 1500mA
Li-Ion battery: 7.4V/4500mAH |
|
Mechanical |
|
Size |
245 x 163 x 52 (mm) |
|
Weight |
1.3KG
(exclusive of packing and accessories) |
Software
：
Operating system: Windows NT, Windows 2000, Windows XP ,VISTA
SecondDesign
|
